DEPARTAMENTO DE ENGENHARIA MECÂNICA
DISCIPLINAS DE DESENHO I/II
NORMAS NP, ISO e ENRELACIONADAS COM ODESENHO TÉCNICO
João M. Pereira Dias
(Versão 1.3)2000/1/4
Janeiro de 2000
NORMAS Versão 1.32
ÍNDICE
NORMAS PORTUGUESAS NP SOBRE DESENHO TÉCNICO..........................................................................3NORMAS PORTUGUESAS NP SOBRE TOLERANCIAMENTO.......................................................................3NORMAS PORTUGUESAS NP SOBRE SOLDADURA......................................................................................4NORMAS PORTUGUESAS NP SOBRE ACABAMENTOS SUPERFICIAIS E ESTADOS DE SUPERFÍCIE.4NORMAS PORTUGUESAS NP SOBRE PEÇAS ROSCADAS............................................................................4NORMAS PORTUGUESAS NP SOBRE REBITES..............................................................................................5NORMAS EUROPEIAS EN SOBRE DESENHO TÉCNICO................................................................................6NORMAS EUROPEIAS EN SOBRE TOLERANCIAMENTO.............................................................................7NORMAS EUROPEIAS EN SOBRE SOLDADURA............................................................................................8NORMAS EUROPEIAS EN RELACIONADAS COM PEÇAS ROSCADAS.....................................................8NORMAS EUROPEIAS EN SOBRE ANILHAS...................................................................................................8NORMAS EUROPEIAS EN SOBRE MOLAS.......................................................................................................9NORMAS EUROPEIAS EN SOBRE ROLAMENTOS..........................................................................................9NORMAS EUROPEIAS EN SOBRE ENGRENAGENS........................................................................................9NORMAS ISO SOBRE DESENHO TÉCNICO...................................................................................................10NORMAS ISO SOBRE TOLERANCIAMENTO DIMENSIONAL....................................................................14NORMAS ISO SOBRE TOLERANCIAMENTO DIMENSIONAL DE PEÇAS ROSCADAS..........................15NORMAS ISO SOBRE TOLERANCIAMENTO DIMENSIONAL DE ENGRENAGENS...............................16NORMAS ISO SOBRE TOLERANCIAMENTO GEOMÉTRICO.....................................................................16NORMAS ISO SOBRE SOLDADURA...............................................................................................................17NORMAS ISO SOBRE ACABAMENTOS SUPERFICIAIS E ESTADOS DE SUPERFÍCIE...........................18NORMAS ISO SOBRE PEÇAS ROSCADAS.....................................................................................................19NORMAS ISO SOBRE ANILHAS......................................................................................................................25NORMAS ISO SOBRE MOLAS..........................................................................................................................26NORMAS ISO SOBRE ROLAMENTOS.............................................................................................................26NORMAS ISO SOBRE ENGRENAGENS...........................................................................................................26NORMAS ISO SOBRE PRODUTOS ESPECÍFICOS E INDIRECTAMENTE RELACIONADAS COM O
DESENHO TÉCNICO...............................................................................................................................28NORMAS ISO SOBRE SIMBOLOS GRÁFICOS USADOS NOS DESENHOS E EM DOCUMENTAÇÃO
TÉCNICA EM GERAL.............................................................................................................................29NORMAS ISO SOBRE DOCUMENTAÇÃO TÉCNICA DO PRODUTO.........................................................31NORMAS ISO SOBRE QUALIDADE.................................................................................................................32NORMAS ISO SOBRE EQUIPAMENTO PARA DESENHO............................................................................34ASPECTOS GERAIS RELACIONADOS COM AS NORMAS ISO..................................................................35LISTA DAS NORMAS POR ORDEM ALFABÉTICA.......................................................................................37NOTA: A AZUL (underline e bold) encontram-se assinaladas as normas disponíveis e actualizadas.
A VERMELHO (Underline e itálico) as normas disponíveis mas desactualizadas.A Verde (Itálico) Norma não disponível mas existe equivalente da ISO** Norma que vai ser adquirida (Livro ISO- Limits, Fits and Surface Properties)
NORMAS Versão 1.33
NORMAS PORTUGUESAS NP SOBRE DESENHO TÉCNICO
NP 48:1968 (3ª Edição), Desenho técnico. Formatos.NP 49:1968 (3ª Edição), Desenho técnico. Modo de dobrar folhas de desenho.NP 62:1961 (2ª Edição), Desenho técnico. Linhas e sua utilização.NP 167:1966 (2ª Edição) Desenho técnico. Figuração de materiais em corte.NP 204:1968 (2ª Edição) Desenho técnico. Legendas.NP 205:1970 (1ª Edição) Desenho técnico. Listas de peças.
NP 265:1962 (1ª Edição) Cotas não toleranciadas. Diferenças para peças metálicas
trabalhadas por arranque de apara
NP 297:1963 (1ª Edição), Desenho técnico. Cotagem.
NP 327:1964 (1ª Edição), Desenho técnico. Representação de vistas.NP 328:1964 (1ª Edição) Desenho técnico. Cortes e secções.
NP 671:1973 (1ª Edição) Desenho técnico. Representação convencional. Convenções de
utilização geral
NP 718:1968 (2ª Edição) Desenho técnico. EsquadriasNORMAS QUE DEIXARAM DE ESTAR EM VIGOR:- 89, 717 (Escalas)
NORMAS PORTUGUESAS NP SOBRE TOLERANCIAMENTO
NP 107:1962 (1ª Edição) Tolerâncias e ajustamentos. TerminologiaNP 189:1962 (1ª Edição) Sistema de tolerâncias. Noções fundamentais.NP 190:1963 (1ª Edição) Sistema de tolerâncias. Simbologia.
NP 366:1964 (1ª Edição) Enchavetamentos. Tolerâncias na largura dos escatéis
NP 716:1968 (1ª Edição) Desenho técnico. Cotagem e especificação de tolerâncias de
elementos cónicos
NP 1895:1982 (1ª Edição) Roscas métricas de perfil triangular ISO para usos gerais.
Tolerâncias. Generalidades CORRESPONDÊNCIA: ISO 965-1:1980 EQV
NORMAS Versão 1.34
NP 1896:1982 (1ª Edição) Roscas métricas de perfil triangular ISO para usos gerais.
Tolerâncias. Dimensões limites. Qualidade média CORRESPONDÊNCIA: ISO965-2:1980 EQV
NP 1897:1982 (1ª Edição) Roscas métricas de perfil triangular ISO para usos gerais.
Tolerâncias. Desvios CORRESPONDÊNCIA: ISO 965-3:1980 EQV
NORMAS PORTUGUESAS NP SOBRE SOLDADURA
NP 1515:1977 (1ª Edição) Soldadura. Representação simbólica nos desenhos CORRESPON-DÊNCIA: ISO 2553:1974
NORMAS PORTUGUESAS NP SOBRE ACABAMENTOS
SUPERFICIAIS E ESTADOS DE SUPERFÍCIE
NP 3915-1:1994 (1ª Edição) Rugosidade de superfícies. Terminologia. Parte 1: Superfície e
seus parâmetros. (CORRESPONDÊNCIA: ISO 4287-1:1984 –Desactualizada existe Ed.97)
NP 3915-2:1994 (1ª Edição) Rugosidade de superfícies. Terminologia. Parte 2: Medição dos
parâmetros de rugosidade de superfície (CORRESPONDÊNCIA: ISO 4287-2:1984 –Desactualizada existe Ed. 97)
NORMAS PORTUGUESAS NP SOBRE PEÇAS ROSCADAS
NP 110:1983 (2ª Edição) Roscas métricas de perfil triangular ISO para usos gerais. Diâmetros
e passos recomendados (CORRESPONDÊNCIA: ISO 262:1973- Desactualizada)NP 155:1985 (3ª Edição) Elementos de ligação roscados e seus acessórios. Nomenclatura
CORRESPONDÊNCIA: ISO 1891:1979 EQV
NP 400:1983 (2ª Edição) Roscas métricas de perfil triangular ISO para usos gerais. Perfil de
base CORRESPONDÊNCIA: ISO 68:1973 EQV. (Disponível edição 1965).
NP 401:1983 (2ª Edição) Roscas métricas de perfil triangular ISO para usos gerais.
Dimensões nominais CORRESPONDÊNCIA: ISO 261:1973 EQV;ISO 724:1978 EQV(Disponível edição 1965).
NORMAS Versão 1.35
NP 1899:1982 (1ª Edição) Parafusos de aço, sem cabeça. Características mecânicas
CORRESPONDÊNCIA: ISO 898-5:1980 EQV
NP 1900:1982 (1ª Edição) Parafusos de cabeça sextavada, parcialmente roscados. Graus de
acabamento A e B CORRESPONDÊNCIA: ISO 4014:1979 EQV*
NORMAS PORTUGUESAS NP SOBRE REBITES
NP 245:1961 (1ª Edição) Rebites semitubulares com cabeça esférica e 3 a 5 mm de diâmetroNP 246:1961 (1ª Edição) Rebites semitubulares com cabeça contrapunçoada plana e 3a 5 mm
de diâmetro
NP 247:1961 (1ª Edição) Rebites semitubulares com cabeça cilíndrica chata e 3 a 6,3 mm de
diâmetro
NP 248:1961 (1ª Edição) Rebites bifurcados com cabeça contrapunçoada plana e 3 a 5mm de
diâmetro
NP 249:1961 (1ª Edição) Rebites com cabeça esférica e 1,6 a 9 mm de diâmetro
NP 250:1961 (1ª Edição) Rebites com cabeça contrapunçoada plana e 1,6 a 9 mm de diâmetroNP 251:1961 (1ª Edição) Rebites com cabeça cilíndrica chata e 1,6 a 9 mm de diâmetroNP 252:1961 (1ª Edição) Furos para rebites
NP 264:1962 (1ª Edição) Rebites. Tipos normalizados
NORMAS Versão 1.36
NORMAS EUROPEIAS EN SOBRE DESENHO TÉCNICO
EN 2851:1992 Série aeroespacial. Marcação de peças e conjuntos, excepto motores. Indicação
nos desenhos
EN 20898-1:1991 Propriedades mecânicas dos elementos de ligação. Parte 1: Parafusos de
cabeça, parafusos com fenda e pernos CORRESPONDÊNCIA: ISO 898-1:1988.EN ISO 4172:1996 Technical drawings. Construction drawings. Drawings for the assembly of
prefabricated structures CORRESPONDÊNCIA: ISO 4172:1991EN ISO 5455:1994 Technical drawings. Scales (Substitui a NP 717)
EN ISO 5457:1999 Tecnical product documentation. Sizes and layout of drawing sheets (ISO
5457:1999)
EN ISO 6410-1:1996 Technical drawings. Screw threads and threaded parts. Part 1: General
conventions CORRESPONDÊNCIA: ISO 6410-1:1993
EN ISO 6410-2:1996 Technical drawings. Screw threads and threaded parts. Part 2: Screw
thread inserts CORRESPONDÊNCIA: ISO 6410-2:1993
EN ISO 6410-3:1996 Technical drawings. Screw threads and threaded parts. Part 3:
Simplified representation CORRESPONDÊNCIA: ISO 6410-3:1993
EN ISO 6411:1997 Technical drawings. Simplified representation of centre holes
CORRESPONDÊNCIA: ISO 6411:1982
EN ISO 6412-1:1994 Technical drawings. Simplified representation of pipelines. Part 1:
General rules and orthogonal representation CORRESPONDÊNCIA: ISO 6412-1:1989EN ISO 6412-2:1994 Technical drawings. Simplified representation of pipelines. Part 2:
Isometric projection. CORRESPONDÊNCIA: ISO 6412-2:1989
EN ISO 6412-3:1996 Technical drawings. Simplified representation of pipelines. Part 3:
Terminal features of ventilation and drainage systems CORRESPONDÊNCIA: ISO6412-3:1993
EN ISO 6413:1994 Technical drawings. Representation of splines and serrations
CORRESPONDÊNCIA: ISO 6413:1988
EN ISO 6414:1994 Technical drawings for glassware CORRESPONDÊNCIA: ISO
6414:1982
EN ISO 6433:1994 Technical drawings. Item references CORRESPONDÊNCIA: ISO
6433:1981
NORMAS Versão 1.37
EN ISO 7437:1996 Technical drawings. Construction drawings. General rules for execution
of production drawings for prefabricated structural componentsCORRESPONDÊNCIA: ISO 7437:1990
EN ISO 7519:1996 Technical drawings. Construction drawings. general principles of
presentation for general arrangement and assembly drawings CORRESPONDÊNCIA:ISO 7519:1991
EN ISO 9222-1:1995 Technical drawings. Seals for dynamic application. Part 1: General
simplified representation CORRESPONDÊNCIA: ISO 9222-1:1989
EN ISO 9222-2:1994 Technical drawings. Seals of dynamic application. Part 2: Detailed
simplified representation CORRESPONDÊNCIA: ISO 9222-2:1989
NORMAS EUROPEIAS EN SOBRE TOLERANCIAMENTO
EN 20286-1:1993 Sistema ISO de tolerâncias e de ajustamento. Parte 1: Base de tolerâncias,
desvios e ajustamentos CORRESPONDÊNCIA: ISO 286-1:1988
EN 20286-2:1993 Sistema ISO de tolerâncias e de ajustamentos. Parte 2: Tabelas dos graus
de tolerância normalizados e dos desvios limites dos furos e dos veiosCORRESPONDÊNCIA: ISO 286-2:1988
EN 22768-1:1993. General tolerances. Part 1: Tolerances for linear and angular dimensions
without individual tolerance indications CORRESPONDÊNCIA: ISO 2768-1:1989EN 22768-2:1993. General tolerances. Part 2: Geometrical tolerances without individual
tolerances indications CORRESPONDÊNCIA: ISO 2768-2:1989
EN ISO 7083:1994 Technical drawings. Symbols for geometrical tolerancing. Proportions and
dimensions. CORRESPONDÊNCIA: ISO 7083:1983NORMAS Versão 1.38
NORMAS EUROPEIAS EN SOBRE SOLDADURA
EN 2574:1990 Série aeroespacial. Soldaduras. Informações nos desenhos
EN 22553:1994 Welded, brazed and soldered joints. Symbolic representation on drawings
CORRESPONDÊNCIA: ISO 2553:1992EN 24063:1992 Welding, brazing, soldering and braze welding of metals. Nomenclature of
processes and reference numbers for symbolic representation on drawingsCORRESPONDÊNCIA: ISO 4063:1990NORMAS EUROPEIAS EN RELACIONADAS COM PEÇAS
ROSCADAS
EN 24014:1991 Hexagon head bolts. Product grades A and B CORRESPONDÊNCIA: ISO
4014:1988 (Catálogo Mattsons)
EN 24015:1991 Hexagon head bolts. Product grade B. Reduced shank (Shank diameter =
pitch diameter) CORRESPONDÊNCIA: ISO 4015:1979.
EN 24016:1991 Hexagon head bolts. Product grade C CORRESPONDÊNCIA: ISO
4016:1988
EN 24017:1991 Hexagon head screws. Product grades A and B CORRESPONDÊNCIA: ISO
4017:1988
EN 24018:1991 Hexagon head screws. Product grade C CORRESPONDÊNCIA: ISO
4018:1988
EN 28676:1991 Hexagon head screws with metric fine pitch thread. Product grades A and B
CORRESPONDÊNCIA: ISO 8676:1988
NORMAS EUROPEIAS EN SOBRE ANILHAS
EN ISO 10644:1998 Screw and washer assemblies with plain washers. Washer hardness
classes 200 HV and 300 HV CORRESPONDÊNCIA: ISO 10644:1998
EN ISO 10673:1998 Plain washers for screw and washer assemblies. Small, normal and large
series. Product grade A CORRESPONDÊNCIA: ISO 10673:1998
EN 28738:1992 Plain washers for clevis pins. Product grade A. CORRESPONDÊNCIA: ISO
8738:1986
NORMAS Versão 1.39
NORMAS EUROPEIAS EN SOBRE MOLAS
EN ISO 2162-1:1996 Technical product documentation. Springs. Part 1: Simplified
representation CORRESPONDÊNCIA: ISO 2162-1:1993EN ISO 2162-2:1996 Technical product documentation. Springs. Part 2: Presentation of data
for cylindrical helical compression springs CORRESPONDÊNCIA: ISO 2162-2:1993EN ISO 2162-3:1996 Technical product documentation. Springs. Part 3: Vocabulary
CORRESPONDÊNCIA: ISO 2162-3:1993NORMAS EUROPEIAS EN SOBRE ROLAMENTOS
EN ISO 8826-1:1995 Technical drawings. Rolling bearings. Part 1: General simplified
representation CORRESPONDÊNCIA: ISO 8826-1:1989EN ISO 8826-2:1997 Technical drawings. Rolling bearings. Part 2: Detailed simplified
representation CORRESPONDÊNCIA: ISO 8826-2:1994NORMAS EUROPEIAS EN SOBRE ENGRENAGENS
EN ISO 2203:1997 Technical drawings. Conventional representation of gears
CORRESPONDÊNCIA: ISO 2203:1973NORMAS Versão 1.310
NORMAS ISO SOBRE DESENHO TÉCNICO
ISO 128:1982 Technical drawings - General principles of presentation . (ISO Book)
ISO/CD 128-1 Technical drawings -- General principles of presentation -- Part 1: Basic
information and indexes (Ed. 1). . (ISO Book)
ISO 128-20:1996 Technical drawings - General principles of presentation - Part 20: Basic
conventions for lines . (ISO Book)
ISO 128-21:1997 Technical drawings - General principles of presentation - Part 21:
Preparation of lines by CAD systems . (ISO Book)
ISO 128-22:1999 Technical drawings -- General principles of presentation -- Part 22: Basic
conventions and applications for leader lines and reference lines (Ed. 1, 8 p, D)ISO 128-23:1999 Technical drawings -- General principles of presentation -- Part 23: Lines
on construction drawings (Ed.1, 12 p, F)
ISO 128-24:1999 Technical drawings -- General principles of presentation -- Part 24: Lines
on mechanical engineering drawings (Ed. 1, 13 p, G)
ISO 128-25:1999 Technical drawings -- General principles of presentation -- Part 25: Lines
on shipbuilding drawings (Ed. 1, 10 p, E)
ISO/DIS 128-30.2 Technical drawings -- General principles of presentation -- Part 30: Basic
conventions for views (Ed. 1, 7 p)
ISO/DIS 128-40 Technical drawings -- General principles of presentation -- Part 40: Basicconventions for cuts and sections (Ed. 1, 5 p)
ISO/DIS 128-41 Technical drawings -- General principles of presentation -- Part 41: Cuts and
sections for mechanical engineering drawings (Ed. 1, 8 p)
ISO/DIS 128-50.2 Technical drawings -- General principles of presentation -- Part 50: Basicconventions for representing areas on cuts and sections (Ed. 1, 5 p)
ISO/DIS 128-60 Technical drawings -- General principles of presentation -- Part 60:
Additional conventions for views, cuts and sections (Ed. 1, 9 p)
ISO/CD 128-71 Technical drawings -- General principles of presentation -- Part 71:
Simplified representation for mechanical engineering (Ed. 1)
ISO 129:1985 Technical drawings - Dimensioning - General principles, definitions, methods
of execution and special indications. (ISO Book)
ISO/DIS 129-1 Technical drawings -- Indication of dimensions and tolerances -- Part 1:
General principles (Ed. 1, 30 p)
NORMAS Versão 1.311
ISO/CD 129-2 Technical drawings -- Dimensioning -- Part 2: Mechanical engineering (Ed. 1)ISO 216:1975 Writing paper and certain classes of printed matter -- Trimmed sizes -- A and Bseries (Ed. 1, 3 p, B)
ISO 1302:1992 Technical drawings - Method of indicating surface texture (ISO Book)ISO/DIS 1302 Geometrical Product Specification (GPS) -- Indication of surface texture in
technical product documentation (Ed. 4, 37 p)ISO 2594:1972 Building drawings - Projection methods
ISO 3098-0:1997 Technical product documentation - Lettering - Part 0: General requirementsISO 3098-1:1974 Technical drawings - Lettering - Part 1: Currently used characters (ISO
Book)
ISO 3098-2:1984 Technical drawings - Lettering - Part 2: Greek characters (ISO Book)ISO 3098-3:1987 Technical drawings - Lettering - Part 3: Diacritical and particular marks for
the Latin alphabet (ISO Book)
ISO 3098-4:1984 Technical drawings - Lettering - Part 4: Cyrillic characters (ISO Book)ISO 3098-5:1997 Technical product documentation - Lettering - Part 5: CAD lettering of the
Latin alphabet, numerals and marks (Disponível edição 1984).
ISO 3272-1:1983 Microfilming of technical drawings and other drawing office documents -Part 1: Operating procedures (ISO Book)
ISO 3272-2:1994 Microfilming of technical drawings and other drawing office documents -Part 2: Quality criteria and control of 35 mm silver gelatin microfilms (ISO Book)ISO 3272-3:1975 Microcopying of technical drawings and other drawing office documents -Part 3: Unitized 35 mm microfilm carriers (ISO Book)
ISO/DIS 3272-3 Microfilming of technical drawings and other drawing office documents -Part 3: Unitized aperture card for 35 mm microfilm
ISO 3272-4:1994 Microfilming of technical drawings and other drawing office documents -Part 4: Microfilming of drawings of special and exceptional elongated sizes (ISO Book)ISO/FDIS 3272-5 Microfilming of technical drawings and other drawing office documents -Part 5: Test procedures for diazo duplicating of microfilm images in aperture cardsISO/DIS 3272-6 Microfilming of technical drawings and other drawing office documents -Part 6: Enlargement from 35 mm microfilm, quality criteria and control
Symbolic representation - Part 4: Basic symbols for process computer, interface, and shared
display/control functions.
ISO 5455:1979 Technical drawings – Scales. (ISO Book)
ISO 5456-1:1996 Technical drawings - Projection methods - Part 1: Synopsis (ISO Book)
NORMAS Versão 1.312
ISO 5456-2:1996 Technical drawings - Projection methods - Part 2: Orthographic
representations (ISO Book)
ISO 5456-3:1996 Technical drawings - Projection methods - Part 3: Axonometric
representations
ISO 5456-4:1996 Technical drawings - Projection methods - Part 4: Central projectionISO 5457:1999 Technical product documentation - Sizes and layout of drawing sheets
(Disponível edição 1980). (ISO Book)
ISO 5845-1:1995 Technical drawings - Simplified representation of the assembly of parts
with fasteners - Part 1: General principles (ISO Book)
ISO 5845-2:1995 Technical drawings - Simplified representation of the assembly of parts
with fasteners - Part 2: Rivets for aerospace equipment (ISO Book)
ISO 6410-1:1993 Technical drawings - Screw threads and threaded parts - Part 1: General
conventions (ISO Book)
ISO 6410-2:1993 Technical drawings - Screw threads and threaded parts - Part 2: Screw
thread inserts (ISO Book)
ISO 6410-3:1993 Technical drawings - Screw threads and threaded parts - Part 3: Simplified
representation (ISO Book)
ISO 6411:1982 Technical drawings - Simplified representation of centre holes (ISO Book)ISO 6412-1:1989 Technical drawings - Simplified representation of pipelines - Part 1:
General rules and orthogonal representation (ISO Book)
ISO 6412-2:1989 Technical drawings - Simplified representation of pipelines - Part
2:Isometric projection (ISO Book)
ISO 6412-3:1993 Technical drawings - Simplified representation of pipelines - Part 3:
Terminal features of ventilation and drainage systems (ISO Book)
ISO 6413:1988 Technical drawings - Representation of splines and serrations. (ISO Book)ISO 6428:1982 Technical drawings - Requirements for microcopying (ISO Book)ISO 6433:1981 Technical drawings -Item references (ISO Book)ISO 7200:1984 Technical drawings - Title blocks (ISO Book)
ISO/DIS 7200-1 Technical product documentation - Document headers and title blocks - Part
1: General structure and content
ISO/DIS 7200-2 Technical product documentation - Document headers and title blocks - Part
2: Title blocks for mechanical engineering
ISO 7573:1983 Technical drawings -Item lists (ISO Book)
NORMAS Versão 1.313
ISO/TR 8545:1984 Technical drawings -Installations - Graphical symbols for automatic
control
ISO 9222-1:1989 Technical drawings - Seals for dynamic application - Part 1: General
simplified representation (ISO Book)
ISO 9222-2:1989 Technical drawings - Seals for dynamic application - Part 2: Detailed
simplified representation (ISO Book)
ISO 10135:1994 Technical drawings - Simplified representation of moulded, cast and forged
parts (ISO Book)
ISO/WD 10135 Technical drawings -- Simplified representation of moulded, cast and forged
parts (Ed. 2)
ISO 10303-101:1994 Industrial automation systems and integration - Product data
representation and exchange - Part 101:Integrated application resources: DraughtingISO 10303-201:1994 Industrial automation systems and integration - Product data
representation and exchange - Part 201: Application protocol: Explicit draughtingISO 10303-202:1996 Industrial automation systems and integration - Product data
representation and exchange - Part 202: Application protocol: Associative draughtingISO/TR 10623:1991 Technical product documentation - Requirements for computer-aided
design and draughting - Vocabulary
ISO/DIS 12650 Document imaging applications - Microfilming of achromatic maps on 35
mm microfilm
ISO 12678-1:1996 Refractory products - Measurement of dimensions and external defects of
refractory bricks - Part 1: Dimensions and conformity to drawings
ISO 13567-1:1998 Technical product documentation - Organization and naming of layers for
CAD - Part 1: Overview and principles
ISO 13567-2:1998 Technical product documentation - Organization and naming of layers for
CAD - Part 2: Concepts, format and codes used in construction documentation
ISO 13715:1994 Technical drawings - Corners - Vocabulary and indication on drawings (ISO
Book)
ISO/FDIS 13715 Technical drawings -- Edges of undefined shape -- Vocabulary and
indication on drawings (Ed. 2)
ISO/DIS 13715 Technical drawings - Edges of undefined shape - Vocabulary and indication
on drawings
ISO/DIS 14985 Hard-copy output of engineering drawings - Specification for the structure of
control files
NORMAS Versão 1.314
ISO 15226:1999 Technical product documentation - Life cycle model and allocation of
documents
ISO/DIS 16018 Technical drawings - Numerically controlled draughting machines -Draughting media and tools for vector plotters
NORMAS ISO SOBRE TOLERANCIAMENTO DIMENSIONAL
ISO 1:1975 ** Standard reference temperature for industrial length measurements. (** ISO
Book Limits)
ISO/TTA 1:1994 Advanced technical ceramics -- Unified classification system (available in
English only) (Ed. 1, 62 p, R)
ISO/WD 1 Geometrical Product Specifications (GPS) -- Reference temperature for industrial
length measurements (Ed. 2)
ISO 286-1:1988 ** ISO system of limits and fits — Part 1: Bases of tolerances, deviations
and fits (** ISO Book Limits)
ISO 286-2:1988 ** ISO system of limits and fits — Part 2: Tables of standard tolerance
grades and limit deviations for holes and shafts (** ISO Book Limits)
ISO/AWI 286-1 Geometrical product specifications (GPS) -- ISO system of limits and fits --Part 1: Bases of tolerances, deviations and fits (Ed. 2)
ISO 370:1975 ** Toleranced dimensions — Conversion from inches into millimeters and
vice versa (** ISO Book Limits)
ISO 406:1987 Technical drawings - Tolerancing of linear and angular dimensions (ISO
Book)
ISO 1119:1998 Geometrical Product Specifications (GPS) — Series of conical tapers and
taper angles (** ISO Book Limits)
ISO 1660:1987 Technical drawings - Dimensioning and tolerancing of profiles (ISO Book)ISO/AWI 1660 Geometrical Product Specifications (GPS) -- Dimensioning and tolerancing ofprofiles (Ed. 3)
ISO 1829:1975 ** Selection of tolerance zones for general purposes (** ISO Book Limits)ISO/R 1938:1971 ** ISO system of limits and fits — Part II: Inspection of plain workpieces
(** ISO Book Limits)
ISO 2538:1998 ** Geometrical Product Specifications (GPS) — Series of angles and slopes
on prisms (** ISO Book Limits)
NORMAS Versão 1.315
ISO 2768-1:1989 ** General tolerances — Part 1: Tolerances for linear and angular
dimensions without individual tolerance indications (** ISO Book Limits)
ISO 2768-2:1989 ** General tolerances — Part 2: Geometrical tolerances for features
without individual tolerance indications (** ISO Book Limits)
ISO 3040:1990 Technical drawings - Dimensioning and tolerancing - Cones (ISO Book)ISO 8062:1994 ** Castings — System of dimensional tolerances and machining allowances
(** ISO Book Limits)
ISO 13920:1996 ** Welding — General tolerances for welded constructions —Dimensions
for lengths and angles — Shape and position (** ISO Book Limits)
ISO/TR 14638:1995 ** Geometrical product specification (GPS) — Masterplan (** ISOBook Limits)
NORMAS ISO SOBRE TOLERANCIAMENTO DIMENSIONAL DE
PEÇAS ROSCADAS
ISO 7-1:1994 ** Pipe threads where pressure-tight joints are made on the threads — Part 1:
Dimensions, tolerances and designation (** ISO Book Limits)
ISO 7-2:1982 ** Pipe threads where pressure-tight joints are made on the threads — Part 2:
Verification by means of limit gauges (** ISO Book Limits)
ISO 228-1:1994 ** Pipe threads where pressure-tight joints are not made on the threads —
Part 1: Dimensions, tolerances and designation (** ISO Book Limits)
ISO 228-2:1987 ** Pipe threads where pressure-tight joints are not made on the threads —
Part 2: Verification by means of limit gauges (** ISO Book Limits)
ISO 965-1:1980 ** ISO general purpose metric screw threads — Tolerances — Part 1:
Principles and basic data (** ISO Book Limits)
ISO 965-2:1980 ** ISO general purpose metric screw threads — Tolerances — Part 2: Limits
of sizes for general purpose bolt and nut threads — Medium quality (** ISO BookLimits)
ISO 965-3:1980 ** ISO general purpose metric screw threads — Tolerances — Part 3:
Deviations for constructional threads (** ISO Book Limits)ISO/R 1501:1970 ** ISO miniature screw threads (** ISO Book Limits)
ISO 1502:1996 ** ISO general-purpose metric screw threads — Gauges and gauging (** ISO
Book Limits)
ISO 2903:1993 ** ISO metric trapezoidal screw threads — Tolerances (** ISO Book Limits)
NORMAS Versão 1.316
ISO 5864:1993 ** ISO inch screw threads — Allowances and tolerances (** ISO Book
Limits)
NORMAS ISO SOBRE TOLERANCIAMENTO DIMENSIONAL DE
ENGRENAGENS
ISO 1328-1:1995 ** Cylindrical gears — ISO system of accuracy — Part 1: Definitions and
allowable values of deviations relevant to corresponding flanks of gear teeth (** ISOBook Limits)
ISO 1328-2:1997 ** Cylindrical gears — ISO system of accuracy — Part 2: Definitions and
allowable values of deviations relevant to radial composite deviations and runoutinformation (** ISO Book Limits)
ISO 4156:1981 ** Straight cylindrical involute splines — Metric module, side fit —
Generalities, dimensions and inspection (** ISO Book Limits)
ISO 4156:1981 /Amd.1:1992 ** Amendment 1:1992 to ISO 4156:1981 Section three:
Inspection
ISO 4468:1982 ** Gear hobs — Single start — Accuracy requirements (** ISO Book Limits)
NORMAS ISO SOBRE TOLERANCIAMENTO GEOMÉTRICO
ISO 1101:1983 Technical drawings -Geometrical tolerancing - Tolerancing of form,
orientation, location and run-out -Generalities, definitions, symbols, indications ondrawings (ISO Book)
ISO/FDIS 1101 Geometrical product specifications (GPS) -- Geometrical tolerancing --Tolerances of form, orientation, location and run-out (Ed. 2)
ISO 1101:1983/ Ext 1:1983 Toleranced characteristics and symbols -- Examples of indication
and interpretation (Ed. 1, A)
ISO 2692:1988 Technical drawings - Geometrical tolerancing - Maximum material principle
(ISO Book)
ISO 2692:1988 Amd 1:1992 Least Material Requirement (ISO Book)
ISO/CD 2692 Technical drawings -- Geometrical tolerancing -- Maximum material principle
(Ed. 2)
NORMAS Versão 1.317
ISO 5458:1998 Geometrical Product Specifications (GPS) - Geometrical tolerancing -Positional tolerancing (Disponível edição 1987). (ISO Book)
ISO 5459:1981 Technical drawings - Geometrical tolerancing - Datums and datum-systems
for geometrical tolerances (ISO Book)
ISO/CD 5459-1 Geometrical Products Specifications (GPS) -- Datums for geometrical
tolerancing -- Part 1: General terms and definitions (Ed. 1)
ISO/CD 5459-2 Geometrical Products Specifications (GPS) -- Datums for geometrical
tolerancing -- Part 2: Datums and datum systems, drawing indications (Ed. 1)
ISO/WD 5459-3 Geometrical Products Specifications (GPS) -- Datums for geometrical
tolerancing -- Part 3: Method for the establishment of datums for the assessment ofgeometrical tolerances (Ed. 1)
ISO/TR 5460:1985 Technical drawings - Geometrical tolerancing - Tolerancing of form,
orientation, location and run-out - Verification principles and methods - Guidelines(ISO Book)
ISO 7083:1983 Technical drawings - Symbols for geometrical tolerancing - Proportions and
dimensions (ISO Book)
ISO 8015:1985 Technical drawings - Fundamental tolerancing principle (ISO Book)ISO 10578:1992 Technical drawings - Tolerancing of orientation and location - Projected
tolerance zone (ISO Book)
ISO 10579:1993 Technical drawings - Dimensioning and tolerancing - Non-rigid parts (ISO
Book)
NORMAS ISO SOBRE SOLDADURA
ISO 2553:1992 Welded, brazed and soldered joints - Symbolic representation on drawings
(ISO Book)
ISO/AWI 2553 Welded, brazed and soldered joints -- Symbolic representation on drawings
(Ed. 4)
ISO 4063:1998 Welding and allied processes - Nomenclature of processes and reference
numbers (Disponível edição 1990). (ISO Book)
NORMAS Versão 1.318
NORMAS ISO SOBRE ACABAMENTOS SUPERFICIAIS E ESTADOS
DE SUPERFÍCIE
ISO 468 - ???? Não existe !
ISO 3274:1996 ** Geometrical Product Specifications (GPS) — Surface texture: Profile
method — Nominal characteristics of contact (stylus) instruments (Incorporates the changes
made by Technical Corrigendum 1:1998 to ISO 3274:1996) (** ISO Book Limits)
ISO 4287:1997 ** Geometrical Product Specifications (GPS) — Surface texture: Profile
method — Terms, definitions and surface texture parameters (Incorporates the changes made
by Technical Corrigendum 1:1998 to ISO 4287:1997) (** ISO Book Limits)
ISO 4288:1996 ** Geometrical Product Specifications (GPS) — Surface texture: Profile
method — Rules and procedures for the assessment of surface texture (Incorporates the
changes made by Technical Corrigendum 1:1998 to ISO 4288:1996) (** ISO Book Limits)
ISO 4291:1985 ** Methods for the assessement of departure from roundness —
Measurement of variations in radius (** ISO Book Limits)
ISO 4292:1985 ** Methods for the assessment of departure from roundness — Measurement
by two- and three-point methods (** ISO Book Limits)
ISO 5436:1985 ** Calibration specimens — Stylus instruments — Types, calibration and use
of specimens (** ISO Book Limits)
ISO 6318:1985 ** Measurement of roundness — Terms, definitions and parameters of
roundness (** ISO Book Limits)
ISO 8785:1998 ** Geometrical Product Specification (GPS) — Surface imperfections —
Terms, definitions and parameters (** ISO Book Limits)
ISO 11562:1996 ** Geometrical Product Specifications (GPS) — Surface texture: Profile
method — Metrological characteristics of phase correct filters (Incorporates the changes
made by Technical Corrigendum 1:1998 to ISO 11562:1996 ) (** ISO Book Limits)
ISO 12085:1996 ** Geometrical Product Specification (GPS) — Surface texture: Profile
method — Motif parameters (Incorporates the changes made by Technical Corrigendum 1:1998 to
ISO 12085:1996 ) (** ISO Book Limits)
ISO 13565-1:1996 ** Geometrical Product Specification (GPS) — Surface texture: Profile
method; Surfaces having stratified functional properties — Part 1: Filtering and generalmeasurement conditions (Incorporates the changes made by Technical Corrigendum 1:1998 to ISO
13565-1:1996) (** ISO Book Limits)
NORMAS Versão 1.319
ISO 13565-2:1996 **. Geometrical Product Specification (GPS) — Surface texture: Profile
method; Surfaces having stratified functional properties — Part 2: Heightcharacterization using the linear material ratio curve (Incorporates the changes made by
Technical Corrigendum 1:1998 to ISO 13565-2:1996) (** ISO Book Limits)
NORMAS ISO SOBRE PEÇAS ROSCADAS
ISO 68-1:1998 ISO general purpose screw threads -- Basic profile -- Part 1: Metric screw
threads
ISO 68-2:1998 ISO general-purpose screw threads -- Basic profile -- Part 2: Inch screw
threads
ISO 225:1983 Fasteners - Bolts, screws, studs and nuts - Symbols and designations of
dimensions
ISO 261:1998 ISO general-purpose metric screw threads -- General plan
ISO 262:1998 ISO general-purpose metric screw threads - Selected sizes for screws, bolts and
nuts
ISO 263:1973 ISO inch screw threads - General plan and selection for screws, bolts and nuts -Diameter range 0.06 to 6 in
ISO 272:1982 Fasteners - Hexagon products - Widths across flatsISO 273:1979 Fasteners - Clearance holes for bolts and screwsISO 299:1987 Machine tool tables - T-slots and corresponding bolts
ISO 691:1997 Assembly tools for screws and nuts - Wrench and socket openings - Tolerances
for general use
ISO 724:1993 ISO general-purpose metric screw threads -- Basic dimensions (Ed. 2, 7 p, D)ISO 885:1976 General purpose bolts and screws - Metric series - Radii under the headISO 888:1976 Bolts, screws and studs - Nominal lengths, and thread lengths for general
purpose bolts
ISO 898-1:1988 Mechanical properties of fasteners - Part 1: Bolts, screws and studs
ISO/DIS 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel - Part
1: Bolts, screws and studs
ISO 898-2:1992 Mechanical properties of fasteners - Part 2: Nuts with specified proof load
values - Coarse thread
NORMAS Versão 1.320
ISO 898-5:1998 Mechanical properties of fasteners made of carbon steel and alloy steel - Part
5: Set screws and similar threaded fasteners not under tensile stresses
ISO 898-6:1994 Mechanical properties of fasteners - Part 6: Nuts with specified proof load
values - Fine pitch thread
ISO 898-7:1992 Mechanical properties of fasteners - Part 7: Torsional test and minimum
torques for bolts and screws with nominal diameters 1 mm to 10 mm
ISO 965-1:1998 ISO general-purpose metric screw threads -- Tolerances -- Part 1: Principles
and basic data (Ed. 3, 18 p, J)
ISO 965-2:1998 ISO general purpose metric screw threads -- Tolerances -- Part 2: Limits of
sizes for general purpose external and internal screw threads -- Medium quality (Ed. 3, 5p, C)
ISO 965-3:1998 ISO general purpose metric screw threads -- Tolerances -- Part 3: Deviations
for constructional screw threads (Ed. 3, 16 p, H)
ISO 965-4:1998 ISO general purpose metric screw threads -- Tolerances -- Part 4: Limits of
sizes for hot-dip galvanized external screw threads to mate with internal screw threadstapped with tolerance position H or G after galvanizing (Ed. 1, 4 p, B)
ISO 965-5:1998 ISO general purpose metric screw threads -- Tolerances -- Part 5: Limits of
sizes for internal screw threads to mate with hot-dip galvanized external screw threadswith maximum size of tolerance position h before galvanizing (Ed. 1, 5 p, C)ISO 1085:1986 Assembly tools for screws and nuts - Double-ended wrenches - Size pairingISO 1207:1992 Slotted cheese head screws - Product grade AISO 1234:1997 Split pins (Ed. 2, 4 p, B) (Pinos De Imobilização)ISO 1478:1983 Tapping screws threadISO/DIS 1478 Tapping screw threadISO 1479:1983 Hexagon head tapping screwsISO 1481:1983 Slotted pan head tapping screws
ISO 1482:1983 Slotted countersunk (flat) head tapping screws (common head style)ISO 1483:1983 Slotted raised countersunk (oval) head tapping screws (common head style)ISO 1580:1994 Slotted pan head screws - Product grade AISO 1703:1983 Assembly tools for screws and nuts - Nomenclature
ISO 1711-1:1996 Assembly tools for screws and nuts - Technical specifications - Part 1:
Hand-operated wrenches and sockets
ISO 1891:1979 Bolts, screws, nuts and accessories - Terminology and nomenclatureISO 2009:1994 Slotted countersunk flat head screws (common head style) - Product grade A
NORMAS Versão 1.321
ISO 2010:1994 Countersunk slotted raised head screws (common head style) - Product
grade A
ISO 2342:1972 Slotted headless screws - Metric series
ISO 2351:1986 Screwdriver bits for slotted head screws, with male hexagon driveISO 3266:1984 Eyebolts for general lifting purposesISO 3269:1988 Fasteners - Acceptance inspectionISO/DIS 3269 Fasteners - Acceptance inspection
ISO 3408-1:1991 Ball screws - Part 1: Vocabulary and designation
ISO 3408-2:1991 Ball screws - Part 2: Nominal diameters and nominal leads - Metric seriesISO 3408-3:1992 Ball screws - Part 3: Acceptance conditions and acceptance testsISO/DIS 3408-4 Ball screws - Part 4: Axial rigidity
ISO/DIS 3408-5 Ball screws - Part 5: Static and dynamic axial load ratings and operational
lifetime
ISO 3506-1:1997 Mechanical properties of corrosion-resistant stainless-steel fasteners - Part
1: Bolts, screws and studs
ISO 3506-2:1997 Mechanical properties of corrosion-resistant stainless-steel fasteners - Part
2: Nuts
ISO 3506-3:1997 Mechanical properties of corrosion-resistant stainless steel fasteners - Part
3: Set screws and similar fasteners not under tensile stress
ISO 3508:1976 Thread run-outs for fasteners with thread in accordance with ISO 261 and ISO
262
ISO 4014:1988 Hexagon head bolts - Product grades A and BISO/DIS 4014 Hexagon head bolts - Product grades A and B
ISO 4015:1979 Hexagon head bolts - Product grade B - Reduced shank (shank diameter
approximately equal to pitch diameter)ISO 4016:1988 Hexagon head bolts - Product grade CISO/DIS 4016 Hexagon head bolts - Product grade C
ISO 4017:1988 Hexagon head screws - Product grades A and BISO/DIS 4017 Hexagon head screws - Product grades A and BISO 4018:1988 Hexagon head screws - Product grade CISO/DIS 4018 Hexagon head screws - Product grade CISO 4026:1993 Hexagon socket set screws with flat pointISO 4027:1993 Hexagon socket set screws with cone pointISO 4028:1993 Hexagon socket set screws with dog point
NORMAS Versão 1.322
ISO 4029:1993 Hexagon socket set screws with cup pointISO 4032:1986 Hexagon nuts, style 1 - Product grades A and BISO/DIS 4032 Hexagon nuts, style 1 - Product grades A and BISO 4033:1979 Hexagon nuts, style 2 - Product grades A and BISO/DIS 4033 Hexagon nuts, style 2 - Product grades A and BISO 4034:1986 Hexagon nuts - Product grade CISO/DIS 4034 Hexagon nuts - Product grade C
ISO 4035:1986 Hexagon thin nuts (chamfered) - Product grades A and BISO/DIS 4035 Hexagon thin nuts (chamfered) - Product grades A and BISO 4036:1979 Hexagon thin nuts - Product grade B (unchamfered)ISO/DIS 4036 Hexagon thin nuts (unchamfered) - Product grade BISO 4161:1999 Hexagon nuts with flange - Coarse threadISO 4162:1990 Hexagon flange bolts - Small series
ISO/DIS 4162 Hexagon bolts with flange - Small series - Product grade combination A/BISO 4229:1977 Assembly tools for screws and nuts - Single-head engineer's wrenches - Gaps
from 50 to 120 mm
ISO 4753:1983 Fasteners - Ends of parts with external metric ISO threadISO 4755:1983 Fasteners - Thread undercuts for external metric ISO threadsISO 4757:1983 Cross recesses for screws
ISO 4759-1:1978 Tolerances for fasteners - Part 1: Bolts, screws and nuts with thread
diameters between 1,6 (inclusive) and 150 mm (inclusive) and product grades A, Band C
ISO/DIS 4759-1 Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product
grades A, B and C
ISO 4759-3:1991 Tolerances for fasteners - Part 3: Plain washers for bolts, screws and nuts
with nominal thread diameters from 1 mm up to and including 150 mm - Product gradesA and C
ISO/DIS 4759-3 Tolerances for fasteners - Part 3: Plain washers for bolts, screws and nuts -Product grades A and C
ISO 4762:1997 Hexagon socket head cap screwsISO 4766:1983 Slotted set screws with flat point
ISO 4775:1984 Hexagon nuts for high-strength structural bolting with large width across flats
- Product grade B - Property classes 8 and 10
NORMAS Versão 1.323
ISO/DIS 4775 Hexagon nuts for high-strength structural bolting with large width across flats -Product grade B - Property classes 8 and 10 (Revision ofISO 4775:1984)ISO 7045:1994 Pan head screws with type H or type Z cross recess - Product grade AISO 7046-1:1994 Countersunk flat head screws (common head style) with type H or type Z
cross recess - Product grade A - Part 1: Steel of property class 4.8
ISO 7046-2:1990 Cross-recessed countersunk flat head screws (common head style) - Grade
A - Part 2: Steel of property class 8.8, stainless steel and non-ferrous metals
ISO 7047:1994 Countersunk raised head screws (common head style) with type H or type Z
cross recess - Product grade A
ISO 7048:1998 Cross recessed cheese head screwsISO 7049:1983 Cross recessed pan head tapping screws
ISO 7050:1983 Cross recessed countersunk (flat) head tapping screws (common head style)ISO 7051:1983 Cross recessed raised countersunk (oval) head tapping screwsISO 7053:1992 Hexagon washer head tapping screws
ISO 7378:1983 Fasteners - Bolts, screws and studs - Split pin holes and wire holesISO 7379:1983 Hexagon socket head shoulder screwsISO 7380:1997 Hexagon socket button head screws
ISO 7411:1984 Hexagon bolts for high-strength structural bolting with large width across
flats (thread lengths according to ISO 888) - Product grade C - Property classes 8.8 and10.9
ISO/DIS 7411 Hexagon bolts for high-strength structural bolting with large width across flats
(thread lengths according to ISO 888) - Product grade C - Property classes 8.8 and 10.9(Revision of ISO 7411:1984)
ISO 7412:1984 Hexagon bolts for high-strength structural bolting with large width across
flats (short thread length) - Product grade C - Property classes 8.8 and 10.9
ISO/DIS 7412 Hexagon bolts for high-strength structural bolting with large width across flats
(short thread length) - Product grade C - Property classes 8.8 and 10.9 (Revision of ISO7412:1984)
ISO 7413:1984 Hexagon nuts for structural bolting, style 1, hot-dip galvanized (oversize
tapped) - Product grades A and B - Property classes 5, 6 and 8
ISO/DIS 7413 Hexagon nuts for structural bolting, style 1, hot-dip galvanized (oversize
tapped) - Product grades A and B - Property classes 5, 6 and 8 (Revision ofISO7413:1984)
NORMAS Versão 1.324
ISO 7414:1984 Hexagon nuts for structural bolting with large width across flats, style 1 -Product grade B - Property class 10
ISO/DIS 7414 Hexagon nuts for structural bolting with large width across flats, style l -Product grade B - Property class 10 (Revision ofISO 7414:1984)
ISO 7417:1984 Hexagon nuts for structural bolting - Style 2, hot-dip galvanized (oversize
tapped) - Product grade A - Property class 9
ISO/DIS 7417 Hexagon nuts for structural bolting, style 2, hot-dip galvanized (oversize
tapped) - Product grade A - Property class 9 (Revision ofISO 7417:1984)ISO 7434:1983 Slotted set screws with cone pointISO 7435:1983 Slotted set screws with long dog pointISO 7436:1983 Slotted set screws with cup point
ISO 8673:1988 Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and BISO/DIS 8673 Hexagon nuts, style 1, with metric fine pitch thread - Product grades A and BISO 8674:1988 Hexagon nuts, style 2, with metric fine pitch thread - Product grades A and BISO/DIS 8674 Hexagon nuts, style 2, with metric fine pitch thread - Product grades A and BISO 8675:1988 Hexagon thin nuts with metric fine pitch thread - Product grades A and BISO/DIS 8675 Hexagon thin nuts (chamfered) with metric fine pitch thread - Product grades
A and B
ISO 8676:1988 Hexagon head screws with metric fine pitch thread - Product grades A and BISO/DIS 8676 Hexagon head screws with metric fine pitch thread - Product grades A and BISO 8677:1986 Cup head square neck bolts with large head - Product grade C
ISO 8678:1988 Cup head square neck bolts with small head and short neck - Product grade BISO 8765:1988 Hexagon head bolts with metric fine pitch thread - Product grades A and BISO/DIS 8765 Hexagon head bolts with metric fine pitch thread - Product grades A and BISO 10663:1999 Hexagon nuts with flange - Fine pitch thread
ISO/DIS 10664 Hexalobular internal driving feature for bolts and screws
ISO/DIS 10666 Drilling screws with tapping screw thread - Mechanical and functional
properties
ISO 10897:1996 Collets for tool holders with taper ratio 1:10 - Collets, hoders,nutsISO 15071:1999 Hexagon bolts with flange - Small series - Product grade A
ISO/DIS 15072 Hexagon bolts with flange with metric fine pitch thread - Small series -Product grade A
ISO/DIS 15073 Hexagon bolts with flange with metric fine pitch thread - Small series -Product grade combination A/B
NORMAS Versão 1.325
ISO/DIS 15480 Hexagon washer head drilling screws with tapping screw threadISO/DIS 15481 Cross recessed pan head drilling screws with tapping screw threadISO/DIS 15482 Cross recessed countersunk head drilling screws with tapping screw threadISO/DIS 15483 Cross recessed raised countersunk head drilling screws with tapping screw
thread
ISO 15488:1996 Collets with 8 degree setting angle for tool shanks - Collets, nuts and fitting
dimensions
NORMAS ISO SOBRE ANILHAS
ISO 887:1983 Plain washers for metric bolts, screws and nuts - General plan
ISO/DIS 887 Plain washers for metric bolts, screws and nuts for general purposes - General
plan
ISO 7089:1983 Plain washers -- Normal series -- Product grade A (Ed. 1, 3 p, B)ISO/FDIS 7089 Plain washers -- Normal series -- Product grade A (Ed. 2)ISO 7091:1983 Plain washers -- Normal series -- Product grade C (Ed. 1, 3 p, B)ISO/FDIS 7091 Plain washers -- Normal series -- Product grade C (Ed. 2)ISO 7092:1983 Plain washers -- Small series -- Product grade A (Ed. 1, 3 p, B)ISO/FDIS 7092 Plain washers -- Small series -- Product grade A (Ed. 2)
ISO 7093:1983 Plain washers -- Large series -- Product grades A and C (Ed. 1, 3 p, B)ISO/FDIS 7093-1 Plain washers -- Large series -- Part 1: Product grade A (Ed. 1)ISO/FDIS 7093-2 Plain washers -- Large series -- Part 2: Product grade C (Ed. 1)ISO 7094:1983 Plain washers -- Extra large series -- Product grade C (Ed. 1, 2 p, A)ISO/FDIS 7094 Plain washers -- Extra large series -- Product grade C (Ed. 2)
ISO 7415:1984 Plain washers for high-strength structural bolting, hardened and tempered
(Ed. 1, 2 p, A)
ISO 8738:1986 Plain washers for clevis pins -- Product grade A (Ed. 1, 3 p, B)
ISO 10669:1999 Plain washers for tapping screw and washer assemblies -- Normal and large
series -- Product grade A (Ed. 1, 4 p, B)
ISO 10673:1998 Plain washers for screw and washer assemblies -- Small, normal and large
series -- Product grade A (Ed. 1, 5 p, C)
NORMAS Versão 1.326
NORMAS ISO SOBRE MOLAS
ISO 2162-1:1993 Technical product documentation - Springs - Part 1: Simplified
representation (ISO Book)
ISO 2162-2:1993 Technical product documentation - Springs - Part 2: Presentation of data
for cylindrical helical compression springs (ISO Book)
ISO 2162-3:1993 Technical product documentation - Springs - Part 3: Vocabulary (ISO
Book)
ISO 6931-1:1994 Stainless steels for springs -- Part 1: Wire (Ed. 2, 11 p, F)ISO 6931-2:1989 Stainless steels for springs -- Part 2: Strip (Ed. 1, 8 p, D)
ISO 8458-1:1989 Steel wire for mechanical springs -- Part 1: General requirements (Ed. 1, 3
p, B)
ISO/CD 8458-1 Steel wire for mechanical springs -- Part 1: General requirements (Ed. 2)ISO 8458-2:1989 Steel wire for mechanical springs -- Part 2: Cold-drawn carbon steel wire
(Ed. 1, 5 p, C)
ISO/CD 8458-2 Steel wire for mechanical springs -- Part 2: Patended cold-drawn unalloyed
steel wire (Ed. 2)
ISO 8458-3:1992 Steel wire for mechanical springs -- Part 3: Oil-hardened and tempered wire
(Ed. 1, 7 p, D)
ISO/CD 8458-3 Steel wire for mechanical springs -- Part 3: Oil-hardened and tempered wire
(Ed. 2)
NORMAS ISO SOBRE ROLAMENTOS
ISO 8826-1:1989 Technical drawings - Rolling bearings - Part 1: General simplified
representation (ISO Book)
ISO 8826-2:1994 Technical drawings - Rolling bearings - Part 2: Detailed simplified
representation (ISO Book)
NORMAS ISO SOBRE ENGRENAGENS
ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering -- Modules
(Ed. 2, 2 p, A)
ISO 2203:1973 Technical drawings - Conventional representation of gears (ISO Book)
NORMAS Versão 1.327
NORMAS ISO SOBRE CONSTRUCTION DRAWINGS
ISO 3766:1995 Construction drawings - Simplified representation of concrete reinforcementISO 4066:1994 Construction drawings - Bar scheduling (ISO Book)
ISO 4068:1978 Building and civil engineering drawings - Reference lines (ISO Book)ISO 4069:1977 Building and civil engineering drawings - Representation of areas on sections
and views - General principles (ISO Book)
ISO 4157-1:1998 Construction drawings - Designation systems - Part 1: Buildings and parts
of buildings (Disponível edição 1980). (ISO Book)
ISO 4157-2:1998 Construction drawings - Designation systems - Part 2: Room names and
numbers (Disponível edição 1982). (ISO Book)
ISO 4157-3:1998 Construction drawings - Designation systems - Part 3: Room identifiersISO 4172:1991 Technical drawings - Construction drawings - Drawings for the assembly of
prefabricated structures. (ISO Book)
ISO 5261:1995 Technical drawings - Simplified representation of bars and profile sections
(ISO Book)
ISO 6284:1996 Construction drawings -Indication of limit deviations (ISO Book)
ISO/TR 7084:1981 Technical drawings - Coding and referencing systems for building and
civil engineering drawings and associated documents (ISO Book)
ISO 7437:1990 Technical drawings - Construction drawings - General rules for execution of
production drawings for prefabricated structural components (ISO Book)
ISO 7518:1983 Technical drawings - Construction drawings - Simplified representation of
demolition and rebuilding (ISO Book)
ISO 7519:1991 Technical drawings - Construction drawings - General principles of
presentation for general arrangement and assembly drawings (ISO Book)
ISO 8048:1984 Technical drawings - Construction drawings - Representation of views,
sections and cuts (ISO Book)
ISO 8560:1986 Technical drawings - Construction drawings - Representation of modular
sizes, lines and grids (ISO Book)
ISO 9431:1990 Construction drawings - Spaces for drawing and for text, and title blocks on
drawing sheets (ISO Book)
ISO/TR 10127:1990 Computer-Aided Design (CAD) Technique - Use of computers for the
preparation of construction drawings (ISO Book)
ISO 11091:1994 Construction drawings - Landscape drawing practice (ISO Book)
NORMAS Versão 1.328
NORMAS ISO SOBRE PRODUTOS ESPECÍFICOS E
INDIRECTAMENTE RELACIONADAS COM O DESENHO TÉCNICO
ISO 6414:1982 Technical drawings for glassware (ISO Book)
ISO 10110-1:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 1: General (ISO Book)
ISO 10110-2:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 2: Material imperfections - Stress birefringence (ISO Book)ISO 10110-3:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 3: Material imperfections - Bubbles and inclusions (ISOBook)
ISO 10110-4:1997 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 4: Material imperfections -Inhomogeneity and striae (ISOBook)
ISO 10110-5:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 5: Surface form tolerances (ISO Book)
ISO 10110-6:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 6: Centring tolerances (ISO Book)
ISO 10110-7:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 7: Surface imperfection tolerances (ISO Book)
ISO 10110-8:1997 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 8: Surface texture
ISO 10110-9:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 9: Surface treatment and coating (ISO Book)
ISO 10110-10:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 10: Table representing data of a lens element (ISO Book)ISO 10110-11:1996 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 11: Non-toleranced data (ISO Book)
ISO 10110-12:1997 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 12: Aspheric surfaces
ISO/DIS 10110-14 Optics and optical instruments - Preparation of drawings for optical
elements and systems - Part 14: Wavefront deformation tolerance for systemscontaining zero-power elements only (Formerly ISO/NP 15000)
NORMAS Versão 1.329
ISO/DIS 10110-15 Optics and optical instruments -- Preparation of drawings for optical
elements and systems -- Part 15: Wavefront deformation tolerance for systemscontaining powered elements (Ed. 1, 37 p, *)
ISO/AWI 10110-16 Optics and optical instruments -- Preparation of drawings for optical
elements and systems -- Part 16: Aspheric diffractive surfaces (Ed. 1)
ISO/CD 10110-17 Optics and optical instruments -- Preparation of drawings for optical
elements and systems -- Part 17: Laser irradiation damage threshold (Ed. 1)
NORMAS ISO SOBRE SIMBOLOS GRÁFICOS USADOS NOSDESENHOS E EM DOCUMENTAÇÃO TÉCNICA EM GERAL
ISO/R 538:1967 Conventional signs to be used in the schemes for the installations of pipeline
systems in ships (ISO Book)
ISO 561:1989 Coal preparation plant -- Graphical symbols (ISO Book)
ISO 710-1:1974 Graphical symbols for use on detailed maps, plans and geological cross-sections -- Part 1: General rules of representation (ISO Book)
ISO 710-2:1974 Graphical symbols for use on detailed maps, plans and geological cross-sections -- Part 2: Representation of sedimentary rocks (ISO Book)
ISO 710-3:1974 Graphical symbols for use on detailed maps, plans and geological cross-sections -- Part 3: Representation of magmatic rocks (ISO Book)
ISO 710-4:1982 Graphical symbols for use on detailed maps, plans and geological cross-sections -- Part 4: Representation of metamorphic rocks (ISO Book)
ISO 710-5:1989 Graphical symbols for use on detailed maps, plans and geological cross-sections -- Part 5: Representation of minerals (ISO Book)
ISO 710-6:1984 Graphical symbols for use on detailed maps, plans and geological cross-sections -- Part 6: Representation of contact rocks and rocks which have undergonemetasomatic, pneumatolytic or hydrothermal transformation or transformation byweathering (ISO Book)
ISO 710-7:1984 Graphical symbols for use on detailed maps, plans and geological cross-sections -- Part 7: Tectonic symbols (ISO Book)
ISO/R 784:1968 Conventional signs to be used in schemes for the installations of sanitary
systems in ships (ISO Book)
NORMAS Versão 1.330
ISO 1219-1:1991 Fluid power systems and components -- Graphic symbols and circuit
diagrams -- Part 1: Graphic symbols (ISO Book)
ISO/CD 1219-1 Fluid power systems and components -- Graphic symbols and circuit
diagrams -- Part 1: Graphic symbols (ISO Book)
ISO 1219-2:1995 Fluid power systems and components -- Graphic symbols and circuit
diagrams -- Part 2: Circuit diagrams (ISO Book)
ISO 1964:1987 Shipbuilding -- Indication of details on the general arrangement plans of
ships (ISO Book)
ISO 3511-1:1977 Process measurement control functions and instrumentation -- Symbolic
representation -- Part 1: Basic requirements (ISO Book)
ISO 3511-2:1984 Process measurement control functions and instrumentation -- Symbolic
representation -- Part 2: Extension of basic requirements (ISO Book)
ISO 3511-3:1984 Process measurement control functions and instrumentation -- Symbolic
representation -- Part 3: Detailed symbols for instrument interconnection diagrams (ISOBook)
ISO 3511-4:1985 Industrial process measurement control functions and instrumentation --Symbolic representation -- Part 4: Basic symbols for process computer, interface, andshared display/control functions (ISO Book)
ISO 3753:1977 Vacuum technology -- Graphical symbols (ISO Book)ISO 3952-1:1981 Kinematic diagrams -- Graphical symbols (ISO Book)ISO 3952-2:1981 Kinematic diagrams -- Graphical symbols (ISO Book)ISO 3952-3:1979 Kinematic diagrams -- Graphical symbols (ISO Book)ISO 3952-4:1984 Kinematic diagrams -- Graphical symbols (ISO Book)ISO 3971:1977 Rice milling -- Symbols and equivalent terms (ISO Book)
ISO 4067-1:1984 Technical drawings -- Installations -- Part 1: Graphical symbols for
plumbing, heating, ventilation and ducting (ISO Book)
ISO 4067-2:1980 Building and civil engineering drawings -- Installations -- Part 2:
Simplified representation of sanitary appliances (ISO Book)
ISO 4067-6:1985 Technical drawings -- Installations -- Part 6: Graphical symbols for supply
water and drainage systems in the ground (ISO Book)ISO 5232:1998 Graphical symbols for textile machinery (ISO Book)
ISO 5784-1:1988 Fluid power systems and components -- Fluid logic circuits -- Part 1:
Symbols for binary logic and related functions (ISO Book)
NORMAS Versão 1.331
ISO 5784-2:1989 Fluid power systems and components -- Fluid logic circuits -- Part 2:
Symbols for supply and exhausts as related to logic symbols (ISO Book)
ISO 5784-3:1989 Fluid power systems and components -- Fluid logic circuits -- Part 3:
Symbols for logic sequencers and related functions (ISO Book)
ISO 5807:1985 Information processing -- Documentation symbols and conventions for data,
program and system flowcharts, program network charts and system resources charts(ISO Book)
ISO 5859:1991 Aerospace -- Graphic symbols for schematic drawings of hydraulic and
pneumatic systems and components (ISO Book)
ISO 6790:1986 Equipment for fire protection and fire fighting -- Graphical symbols for fire
protection plans – Specification (ISO Book)
ISO 6829:1983 Flowchart symbols and their use in micrographics (ISO Book)
ISO 8790:1987 Information processing systems -- Computer system configuration diagram
symbols and conventions (ISO Book)
ISO 9878:1990 Micrographics -- Graphical symbols for use in microfilming (ISO Book)ISO 10628:1997 Flow diagrams for process plants -- General rules (ISO Book)
NORMAS ISO SOBRE DOCUMENTAÇÃO TÉCNICA DO PRODUTO
ISO 10209-1:1992 Technical product documentation -- Vocabulary -- Part 1: Terms relating
to technical drawings: general and types of drawings (ISO Book)
ISO 10209-2:1993 Technical product documentation -- Vocabulary -- Part 2: Terms relating
to projection methods (ISO Book)
ISO 10209-4:1999 Technical product documentation -- Vocabulary -- Part 4: Terms relating
to construction documentation (Ed. 1, K)
ISO 11442-1:1993 Technical product documentation -- Handling of computer-based technical
information -- Part 1: Security requirements (ISO Book)
ISO/AWI 11442-1 Technical product documentation -- Handling of computer-based technical
information -- Part 1: Security requirements (Ed. 2)
ISO 11442-2:1993 Technical product documentation -- Handling of computer-based technical
information -- Part 2: Original documentation (ISO Book)
NORMAS Versão 1.332
ISO/AWI 11442-2 Technical product documentation -- Handling of computer-based technical
information -- Part 2: Original documentation (Ed. 2)
ISO 11442-3:1993 Technical product documentation -- Handling of computer-based technical
information -- Part 3: Phases in the product design process (ISO Book)
ISO/AWI 11442-3 Technical product documentation -- Handling of computer-based technical
information -- Part 3: Phases in the product design process (Ed. 2)
ISO 11442-4:1993 Technical product documentation -- Handling of computer-based technical
information -- Part 4: Document management and retrieval systems (ISO Book)ISO/AWI 11442-4 Technical product documentation -- Handling of computer-based technical
information -- Part 4: Document management and retrieval systems (Ed. 2)
ISO 11442-5 Technical product documentation -- Handling of computer-based technical
information -- Part 5: Documentation in the conceptual design stage of the developmentphase (Ed. 1, 3 p)
ISO/DIS 11442-6 Technical product documentation -- Handling of computer-based technical
information -- Part 6: Rules for revision (Ed. 1, 4 p)
ISO/DIS 11442-7 Technical product documentation -- Handling of computer-based technical
information -- Part 7: Structuring CAD files from an administrative point of wiew (Ed.1, 4 p)
ISO/DIS 11442-8 Technical product documentation -- Handling of computer-based technical
information -- Part 8: Data fields for title blocks, item lists and revision blocks (Ed. 1, 7p)
ISO/DIS 11442-9 Technical product documentation -- Handling of computer-based technical
information -- Part 9: Terminology (Ed. 1, 6 p)
NORMAS ISO SOBRE QUALIDADE
ISO 8402:1994 Quality management and quality assurance -- Vocabulary (Ed. 2, R)ISO/DIS 9000 Quality management systems -- Fundamentals and vocabulary (Ed. 2)ISO 9000-1:1994 Quality management and quality assurance standards -- Part 1: Guidelines
for selection and use (Ed. 1, 18 p, J)
NORMAS Versão 1.333
ISO 9000-2:1997 Quality management and quality assurance standards -- Part 2: Generic
guidelines for the application of ISO 9001, ISO 9002 and ISO 9003 (Ed. 2, 26 p, M)ISO 9000-3:1997 Quality management and quality assurance standards -- Part 3: Guidelines
for the application of ISO 9001:1994 to the development, supply, installation andmaintenance of computer software (Ed. 2, 32 p, P)
ISO 9000-4:1993 Quality management and quality assurance standards -- Part 4: Guide to
dependability programme management (Ed. 1, L)
ISO 9001:1994 Quality systems -- Model for quality assurance in design, development,
production, installation and servicing (Ed. 2, 11 p, F)ISO/DIS 9001 Quality management systems -- Requirements (Ed. 3)ISO 9001:1994/Cor 1:1995 (available in French only) (Ed. 1, *)
ISO 9002:1994 Quality systems -- Model for quality assurance in production, installation and
servicing (Ed. 2, 10 p, E)
ISO 9002:1994/Cor 1:1995 (available in French only) (Ed. 1, *)
ISO 9003:1994 Quality systems -- Model for quality assurance in final inspection and test
(Ed. 2, 7 p, D)
ISO 9003:1994/Cor 1:1994 (available in French only) (Ed. 1, *)ISO 9003:1994/Cor 2:1995 (available in French only) (Ed. 1, *)
ISO/DIS 9004 Quality management systems -- Guidelines for performance improvements
(Ed. 2)
ISO 9004-1:1994 Quality management and quality system elements -- Part 1: Guidelines (Ed.
1, 23 p, L)
ISO 9004-2:1991 Quality management and quality system elements -- Part 2: Guidelines for
services (Ed. 1, 18 p, J)
ISO 9004-2:1991/Cor 1:1994 (available in French only) (Ed. 1, *)
ISO 9004-3:1993 Quality management and quality system elements -- Part 3: Guidelines for
processed materials (Ed. 1, 21 p, L)
ISO 9004-4:1993 Quality management and quality system elements -- Part 4: Guidelines for
quality improvement (Ed. 1, 25 p, M)ISO 9004-4:1993/Cor 1:1994 (Ed. 1, 2 p, *)
NORMAS Versão 1.334
NORMAS ISO SOBRE EQUIPAMENTO PARA DESENHO
ISO 9175-1:1988 Tubular tips for hand-held technical pens using India ink on tracing paper --Part 1: Definitions, dimensions, designation and marking (ISO Book)
ISO 9175-2:1988 Tubular tips for hand-held technical pens using India ink on tracing paper --Part 2: Performance, test parameters and test conditions (ISO Book)ISO 9176:1988 Tubular technical pens -- Adaptor for compasses (ISO Book)
ISO 9177-1:1989 Mechanical pencils -- Part 1: Classification, dimensions, performance
requirements and testing (ISO Book)
ISO 9177-2:1989 Mechanical pencils -- Part 2: Black leads -- Classification and dimensions
(ISO Book)
ISO 9177-3:1994 Mechanical pencils -- Part 3: Black leads -- Bending strengths of HB leads
(ISO Book)
ISO 9178-1:1988 Templates for lettering and symbols -- Part 1: General principles and
identification markings (ISO Book)
ISO 9178-2:1988 Templates for lettering and symbols -- Part 2: Slot widths for wood-cased
pencils, clutch pencils and fine-lead pencils (ISO Book)
ISO 9178-3:1989 Templates for lettering and symbols -- Part 3: Slot widths for technical pens
with tubular tips in accordance with ISO 9175-1 (ISO Book)
ISO 9179-1:1988 Technical drawings -- Numerically controlled draughting machines -- Part
1: Vocabulary (ISO Book)
ISO 9180:1988 Black leads for wood-cased pencils -- Classification and diameters (ISO
Book)
ISO 9957-1:1992 Fluid draughting media -- Part 1: Water-based India ink -- Requirements
and test conditions (Ed. 1, 6 p, C)
ISO 9957-2:1995 Fluid draughting media -- Part 2: Water-based non-India ink --Requirements and test conditions (ISO Book)
ISO 9957-3:1997 Fluid draughting media -- Part 3: Water-based coloured draughting inks --Requirements and test conditions (Ed. 1, 10 p, E)
ISO 9958-1:1992 Draughting media for technical drawings -- Draughting film with polyester
base -- Part 1: Requirements and marking (ISO Book)
ISO 9958-2:1992 Draughting media for technical drawings -- Draughting film with polyester
base -- Part 2: Determination of properties (ISO Book)
NORMAS Versão 1.335
ISO 9959-1:1992 Numerically controlled draughting machines -- Drawing test for the
evaluation of performance -- Part 1: Vector plotters (ISO Book)
ISO 9959-2:1999 Numerically controlled draughting machines -- Draughting test for
evaluation of performance -- Part 2: Monochrome raster plotters (Ed. 1, 15 p, H)ISO 9960-1:1992 Draughting instruments with or without graduation -- Part 1: Draughting
scale rules (ISO Book)
ISO 9960-2:1994 Draughting instruments with or without graduation -- Part 2: Protractors
(ISO Book)
ISO 9960-3:1994 Draughting instruments with or without graduation -- Part 3: Set squares
(ISO Book)
ISO 9961:1992 Draughting media for technical drawings -- Natural tracing paper (ISO Book)ISO 9962-1:1992 Manually operated draughting machines -- Part 1: Definitions,
classification and designation (ISO Book)
ISO 9962-2:1992 Manually operated draughting machines -- Part 2: Characteristics,
performance, inspection and marking (ISO Book)
ISO 9962-3:1994 Manually operated draughting machines -- Part 3: Dimensions of scale rule
chuck plates (ISO Book)
ISO 11540:1993 Caps for writing and marking instruments intended for use by children up to
14 years of age -- Safety requirements (ISO Book)
ASPECTOS GERAIS RELACIONADOS COM AS NORMAS ISO
Reference number - This consists of a prefix, a serial number and the year ofpublication. The prefix will usually be \"ISO\" to indicate that the publication is an ISOInternational Standard.
The prefix ISO/IEC denotes a joint ISO and IEC (International ElectrotechnicalCommission) publication. ISO/IEC International Standards are developed by Joint ISO/IECTechnical Committee JTC 1. A few IEC International Standards with the prefix IEC, whichbelong to JTC 1, have also been included in the Catalogue. Similarly to the ISO/IEC prefix,the ISO/CIE prefix denotes a joint ISO and CEI (International Commission on Illumination)International Standard.
The prefix ISO/TR or ISO/IEC TR denotes an ISO or ISO/IEC technical report. Thesereports are published in certain circumstances to provide either interim progress reports or
NORMAS Versão 1.336
factual information of a kind different from that normally incorporated in an InternationalStandard.
The prefix ISO/IEC ISP denotes an ISO/IEC International Standardized Profile - aninternally agreed, harmonized document which identifies a standard or group of standards,together with options and parameters, necessary to perform a function or set of functions.The prefix ISO/TTA denotes an ISO publication named technical trend assessment.These publications were established for responding to the need for global collaboration onstandardization at early stages of technological innovations. They are the result of either directcooperation with pre-standardization organizations or ad hoc workshops of experts concernedwith standardization needs and trends in emerging fields.
The prefix ISO Guide or ISO/IEC Guide denotes ISO or ISO/IEC guides, which aredocuments of a general nature on matters related to international standardization, such asguidelines, policy statements, model rules or application guides.
The prefix ISO/R denotes an ISO recommendation. This designation was used up to1972, when ISO began to publish International Standards. Since then, ISO recommendationshave gradually been revised and republished as International Standards. A limited number ofISO recommendations, for which the revision and transformation into International Standardshave not yet been completed, remain available.
The prefix is followed by a serial number which may include a part number, separatedby a hyphen from the main number. The serial number is followed by the year of publicationseparated from the serial number by a colon.
Prefixes containing the abbreviations DIS, DTR and DISP belong respectively to draftInternational Standards, draft technical reports and draft International Standardized Profiles.An initial F may be used in conjunction with one of the foregoing prefixes to denote a finaldraft, e.g. FDIS indicates a final draft International Standard. Some draft documents, such asdraft guides or draft amendments to International Standards, do not take a special prefix orcarry the word draft.
All draft documents may be identified by the fact that reference numbers of drafts donot include a year of publication.
NORMAS Versão 1.337
LISTA DAS NORMAS POR ORDEM ALFABÉTICA
EN 20286-1:1993, 7EN 20286-2:1993, 7EN 20898-1:1991, 6EN 22553:1994, 8EN 22768-1:1993, 7EN 22768-2:1993, 7EN 24014:1991, 8EN 24015:1991, 8EN 24016:1991, 8EN 24017:1991, 8EN 24018:1991, 8EN 24063:1992, 8EN 2574:1990, 8EN 2851:1992, 6EN 28676:1991, 8EN 28738:1992, 8EN ISO 10644:1998, 8EN ISO 10673:1998, 8EN ISO 2162-1:1996, 9EN ISO 2162-2:1996, 9EN ISO 2162-3:1996, 9EN ISO 2203:1997, 9EN ISO 4172:1996, 6EN ISO 5455:1994, 6EN ISO 5457:1999, 6EN ISO 6410-1:1996, 6EN ISO 6410-2:1996, 6EN ISO 6410-3:1996, 6EN ISO 6411:1997, 6EN ISO 6412-1:1994, 6EN ISO 6412-2:1994, 6EN ISO 6412-3:1996, 6EN ISO 6413:1994, 6EN ISO 6414:1994, 6EN ISO 6433:1994, 6EN ISO 7083:1994, 7EN ISO 7437:1996, 7EN ISO 7519:1996, 7EN ISO 8826-1:1995, 9EN ISO 8826-2:1997, 9EN ISO 9222-1:1995, 7EN ISO 9222-2:1994, 7
ISO 1:1975, 14ISO 10110-1:1996, 28ISO 10110-10:1996, 28ISO 10110-11:1996, 28ISO 10110-12:1997, 28ISO 10110-2:1996, 28ISO 10110-3:1996, 28ISO 10110-4:1997, 28ISO 10110-5:1996, 28ISO 10110-6:1996, 28ISO 10110-7:1996, 28ISO 10110-8:1997, 28ISO 10110-9:1996, 28ISO 10135:1994, 13
ISO 10209-1:1992, 31ISO 10209-2:1993, 31ISO 10209-4:1999, 31ISO 10303-101:1994, 13ISO 10303-201:1994, 13ISO 10303-202:1996, 13ISO 10578:1992, 17ISO 10579:1993, 17ISO 10628:1997, 31ISO 10663:1999, 24ISO 10669:1999, 25ISO 10673:1998, 25ISO 1085:1986, 20ISO 10897:1996, 24ISO 1101:1983, 16
ISO 1101:1983/ Ext 1:1983, 16
ISO 11091:1994, 27ISO 1119:1998, 14ISO 11442-1:1993, 31ISO 11442-2:1993, 31ISO 11442-3:1993, 32ISO 11442-4:1993, 32ISO 11442-5, 32ISO 11540:1993, 35ISO 11562:1996, 18ISO 1207:1992, 20ISO 12085:1996, 18ISO 1219-1:1991, 30ISO 1219-2:1995, 30ISO 1234:199, 20ISO 12678-1:1996, 13ISO 128:1982, 10ISO 128-20:1996, 10ISO 128-21:1997, 10ISO 128-22:1999, 10ISO 128-23:1999, 10ISO 128-24:1999, 10ISO 128-25:1999, 10ISO 129:1985, 10ISO 1302:1992, 11ISO 1328-1:1995, 16ISO 1328-2:1997, 16ISO 13565-1:1996, 18ISO 13565-2:1996, 19ISO 13567-1:1998, 13ISO 13567-2:1998, 13ISO 13715:1994, 13ISO 13920:1996, 15ISO 1478:1983, 20ISO 1479:1983, 20ISO 1481:1983, 20ISO 1482:1983, 20ISO 1483:1983, 20ISO 1502:1996, 15ISO 15071:1999, 24ISO 15226:1999, 14
ISO 15488:1996, 25ISO 1580:1994, 20ISO 1660:1987, 14ISO 1703:1983, 20ISO 1711-1:1996, 20ISO 1829:1975, 14ISO 1891:1979, 20ISO 1964:1987, 30ISO 2009:1994, 20ISO 2010:1994, 21ISO 216:1975, 11ISO 2162-1:1993, 26ISO 2162-2:1993, 26ISO 2162-3:1993, 26ISO 2203:1973, 26ISO 225:1983, 19ISO 228-1:1994, 15ISO 228-2:1987, 15ISO 2342:1972, 21ISO 2351:1986, 21ISO 2538:1998, 14ISO 2553:1992, 17ISO 2594:1972, 11ISO 261:1998, 19ISO 262:1998, 19ISO 263:1973, 19ISO 2692:1988, 16
ISO 2692:1988 Amd 1:1992,
16
ISO 272:1982, 19ISO 273:1979, 19ISO 2768-1:1989, 15ISO 2768-2:1989, 15ISO 286-1:1988, 14ISO 286-2:1988, 14ISO 2903:1993, 15ISO 299:1987, 19ISO 3040:1990, 15ISO 3098-1:1974, 11ISO 3098-2:1984, 11ISO 3098-3:1987, 11ISO 3098-4:1984, 11ISO 3098-5:1997, 11ISO 3266:1984, 21ISO 3269:1988, 21ISO 3272-1:1983, 11ISO 3272-2:1994, 11ISO 3272-3:1975, 11ISO 3272-4:1994, 11ISO 3274:1996, 18ISO 3408-1:1991, 21ISO 3408-2:1991, 21ISO 3408-3:1992, 21ISO 3506-1:1997, 21ISO 3506-2:1997, 21ISO 3506-3:1997, 21
NORMAS Versão 1.3ISO 3508:1976, 21ISO 3511-1:1977, 30ISO 3511-2:1984, 30ISO 3511-3:1984, 30ISO 3511-4:1985, 30ISO 370:1975, 14ISO 3753:1977, 30ISO 3766:1995, 27ISO 3952-1:1981, 30ISO 3952-2:1981, 30ISO 3952-3:1979, 30ISO 3952-4:1984, 30ISO 3971:1977, 30ISO 4014:1988, 21ISO 4015:1979, 21ISO 4016:1988, 21ISO 4017:1988, 21ISO 4018:1988, 21ISO 4026:1993, 21ISO 4027:1993, 21ISO 4028:1993, 21ISO 4029:1993, 22ISO 4032:1986, 22ISO 4033:1979, 22ISO 4034:1986, 22ISO 4035:1986, 22ISO 4036:1979, 22ISO 406:1987, 14ISO 4063:1998, 17ISO 4066:1994, 27ISO 4067-1:1984, 30ISO 4067-2:1980, 30ISO 4067-6:1985, 30ISO 4068:1978, 27ISO 4069:1977, 27ISO 4156:1981, 16
ISO 4156:1981 /Amd.1:1992,
16
ISO 4157-1:1998, 27ISO 4157-2:1998, 27ISO 4157-3:1998, 27ISO 4161:1999, 22ISO 4162:1990, 22ISO 4172:1991, 27ISO 4229:1977, 22ISO 4287:1997, 18ISO 4288:1996, 18ISO 4291:1985, 18ISO 4292:1985, 18ISO 4468:1982, 16ISO 4753:1983, 22ISO 4755:1983, 22ISO 4757:1983, 22ISO 4759-1:1978, 22ISO 4762:1997, 22ISO 4766:1983, 22ISO 4775:1984, 22ISO 5232:1998, 30ISO 5261:1995, 27ISO 54:1996, 26ISO 5436:1985, 18ISO 5455:1979, 11ISO 5456-1:1996, 11ISO 5456-2:1996, 12ISO 5456-3:1996, 12ISO 5457:1999, 12ISO 5458:1998, 17ISO 5459:1981, 17ISO 561:1989, 29ISO 5784-1:1988, 30ISO 5784-2:1989, 31ISO 5784-3:1989, 31ISO 5807:1985, 31ISO 5845-1:1995, 12ISO 5845-2:1995, 12ISO 5859:1991, 31ISO 5864:1993, 16ISO 6284:1996, 27ISO 6318:1985, 18ISO 6410-1:1993, 12ISO 6410-2:1993, 12ISO 6410-3:1993, 12ISO 6411:1982, 12ISO 6412-1:1989, 12ISO 6412-2:1989, 12ISO 6412-3:1993, 12ISO 6413:1988, 12ISO 6414:1982, 28ISO 6428:1982, 12ISO 6433:1981, 12ISO 6790:1986, 31ISO 68-1:1998, 19ISO 68-2:1998, 19ISO 6829:1983, 31ISO 691:1997, 19ISO 6931-1:1994, 26ISO 6931-2:1989, 26ISO 7045:1994, 23ISO 7046-1:1994, 23ISO 7046-2:1990, 23ISO 7047:1994, 23ISO 7048:1998, 23ISO 7049:1983, 23ISO 7050:1983, 23ISO 7051:1983, 23ISO 7053:1992, 23ISO 7083:1983, 17ISO 7089:1983, 25ISO 7091:1983, 25ISO 7092:1983, 25ISO 7093:1983, 25ISO 7094:1983, 25ISO 7-1:1994, 15ISO 710-1:1974, 29ISO 710-2:1974, 29ISO 710-3:1974, 29ISO 710-4:1982, 29ISO 710-5:198, 29ISO 710-6:1984, 29ISO 710-7:1984, 29
38
ISO 7-2:1982, 15ISO 7200:1984, 12ISO 724:1993, 19ISO 7378:1983, 23ISO 7379:1983, 23ISO 7380:1997, 23ISO 7411:1984, 23ISO 7412:1984, 23ISO 7413:1984, 23ISO 7414:1984, 24ISO 7415:1984, 25ISO 7417:1984, 24ISO 7434:1983, 24ISO 7435:1983, 24ISO 7436:1983, 24ISO 7437:1990, 27ISO 7518:1983, 27ISO 7519:1991, 27ISO 7573:1983, 12ISO 8015:1985, 17ISO 8048:1984, 27ISO 8062:1994, 15ISO 8402:1994, 32ISO 8458-1:1989, 26ISO 8458-2:1989, 26ISO 8458-3:1992, 26ISO 8560:1986, 27ISO 8673:1988, 24ISO 8674:1988, 24ISO 8675:1988, 24ISO 8676:1988, 24ISO 8677:1986, 24ISO 8678:1988, 24ISO 8738:1986, 25ISO 8765:1988, 24ISO 8785:1998, 18ISO 8790:1987, 31ISO 8826-1:1989, 26ISO 8826-2:1994, 26ISO 885:1976, 19ISO 887:1983, 25ISO 898-1:1988, 19ISO 898-2:1992, 19ISO 898-5:1998, 20ISO 898-6:1994, 20ISO 898-7:1992, 20ISO 9000-1:1994, 32ISO 9000-2:1997, 33ISO 9000-3:1997, 33ISO 9000-4:1993, 33ISO 9001:1994, 33
ISO 9001:1994/Cor 1:1995, 33
ISO 9002:1994, 33
ISO 9002:1994/Cor 1:1995, 33
ISO 9003:1994, 33
ISO 9003:1994/Cor 1:1994, 33ISO 9003:1994/Cor 2:1995, 33
ISO 9004-1:1994, 33ISO 9004-2:1991, 33
NORMAS Versão 1.3ISO 9004-2:1991/Cor 1:1994,
33
ISO 9004-3:1993, 33ISO 9004-4:1993, 33ISO 9004-4:1993/Cor 1:1994,
33
ISO 9175-1:1988, 34ISO 9175-2:1988, 34ISO 9176:1988, 34ISO 9177-1:1989, 34ISO 9177-2:1989, 34ISO 9177-3:1994, 34ISO 9178-1:1988, 34ISO 9178-2:1988, 34ISO 9178-3:1989, 34ISO 9179-1:1988, 34ISO 9180:1988, 34ISO 9222-1:1989, 13ISO 9222-2:1989, 13ISO 9431:1990, 27ISO 965-1:1980, 15ISO 965-1:1998, 20ISO 965-2:1980, 15ISO 965-2:1998, 20ISO 965-3:1980, 15ISO 965-3:1998, 20ISO 965-4:1998, 20ISO 965-5:1998, 20ISO 9878:1990, 31ISO 9957-1:1992, 34ISO 9957-2:1995, 34ISO 9957-3:1997, 34ISO 9958-1:1992, 34ISO 9958-2:1992, 34ISO 9959-1:1992, 35ISO 9959-2:1999, 35ISO 9960-1:1992, 35ISO 9960-2:1994, 35ISO 9960-3:1994, 35ISO 9961:1992, 35ISO 9962-1:1992, 35ISO 9962-2:1992, 35ISO 9962-3:1994, 35ISO/AWI 10110-16, 29ISO/AWI 11442-1, 31ISO/AWI 11442-2, 32ISO/AWI 11442-3, 32ISO/AWI 11442-4, 32ISO/AWI 2553, 17ISO/AWI 286-1, 14ISO/CD 10110-17, 29ISO/CD 1219-1, 30ISO/CD 128-71, 10ISO/CD 129-2, 11ISO/CD 2692, 16ISO/CD 5459-1, 17ISO/CD 5459-2, 17ISO/CD 8458-1, 26ISO/CD 8458-2, 26ISO/CD 8458-3, 26ISO/DIS 10110-14, 28ISO/DIS 10110-15, 29ISO/DIS 10664, 24ISO/DIS 10666, 24ISO/DIS 11442-6, 32ISO/DIS 11442-7, 32ISO/DIS 11442-8, 32ISO/DIS 11442-9, 32ISO/DIS 128-30.2, 10ISO/DIS 128-40, 10ISO/DIS 128-41, 10ISO/DIS 128-50.2, 10ISO/DIS 128-60, 10ISO/DIS 129-1, 10ISO/DIS 1302, 11ISO/DIS 1478, 20ISO/DIS 14985, 13ISO/DIS 15072, 24ISO/DIS 15073, 24ISO/DIS 15480, 25ISO/DIS 15481, 25ISO/DIS 15482, 25ISO/DIS 15483, 25ISO/DIS 16018, 14ISO/DIS 3269, 21ISO/DIS 3408-4, 21ISO/DIS 3408-5, 21ISO/DIS 4014, 21ISO/DIS 4016, 21ISO/DIS 4017, 21ISO/DIS 4018, 21ISO/DIS 4032, 22ISO/DIS 4033, 22ISO/DIS 4034, 22ISO/DIS 4035, 22ISO/DIS 4036, 22ISO/DIS 4162, 22ISO/DIS 4759-1, 22ISO/DIS 4759-3, 22ISO/DIS 4775, 23ISO/DIS 7411, 23ISO/DIS 7412, 23ISO/DIS 7413, 23ISO/DIS 7414, 24ISO/DIS 7417, 24ISO/DIS 8673, 24ISO/DIS 8674, 24ISO/DIS 8675, 24ISO/DIS 8676, 24ISO/DIS 8765, 24ISO/DIS 887, 25ISO/DIS 898-1, 19ISO/DIS 9000, 32ISO/DIS 9001, 3339
ISO/DIS 9004, 33ISO/FDIS 1101, 16ISO/FDIS 7089, 25ISO/FDIS 7091, 25ISO/FDIS 7092, 25ISO/FDIS 7093-1, 25ISO/FDIS 7093-2, 25ISO/FDIS 7094, 25ISO/R 1501:1970, 15ISO/R 1938:1971, 14ISO/R 538:1967, 29ISO/R 784:1968, 29ISO/TR 10127:1990, 27ISO/TR 14638:1995, 15ISO/TR 5460:1985, 17ISO/TR 7084:1981, 27ISO/TTA 1:1994, 14ISO/WD 1, 14ISO/WD 5459-3, 17NP 107:1962, 3NP 110:1983, 4NP 1515:1977, 4NP 155:1985, 4NP 167:1966, 3NP 189:1962, 3NP 1895:1982, 3NP 1896:1982, 4NP 1897:1982, 4NP 1899:1982, 5NP 190:1963, 3NP 1900:1982, 5NP 204:1968, 3NP 205:1970, 3NP 245:1961, 5NP 246:1961, 5NP 247:1961, 5NP 248:1961, 5NP 249:1961, 5NP 250:1961, 5NP 251:1961, 5NP 252:1961, 5NP 264:1962, 5NP 265:1962, 3NP 297:1963, 3NP 327:1964, 3NP 328:1964, 3NP 366:1964, 3NP 3915-1:1994, 4NP 3915-2:1994, 4NP 400:1983, 4NP 401:1983, 4NP 48:1968, 3NP 49:1968, 3NP 62:1961, 3NP 671:1973, 3NP 716:1968, 3NP 718:1968, 3
因篇幅问题不能全部显示，请点此查看更多更全内容